• Code Composer Setup / Driver Support
• Default Configuration Switch Settings
• PCI Configuration Switch Settings
• Reference voltage noise

Code Composer Setup / Driver Support (07/19/07)
The supported debug target for DaVinci HD is Code Composer 3.3. If you are using Spectrum Digital JTAG emulators, you can get DaVinci HD EVM CCSetup configurations and drivers tested against the DaVinci HD silicon by installing the latest version of our emulation driver packages at:

http://support.spectrumdigital.com/ccs33 (Spectrum Digital XDS510 Series Emulators)
http://support.spectrumdigital.com/ccs3x_xds560r (Spectrum Digital XDS560R Series Emulators)

Configuration Switch Settings (06/27/07)
Here is the configuration for SW3 on the DaVinci HD board.

SW3:
    [OFF=0][ON=1]
     /----------\ 
     | # OFF ON |    [OFF=0]          [ON=1]
BM0 -| 1 X      |--  *BM[0]=0         BM[0]=1
BM1 -| 2 X      |--  *BM[1]=0         BM[1]=1
BM2 -| 3 X      |--  *BM[2]=0         BM[2]=1
BM3 -| 4 X      |--  *BM[3]=0         BM[3]=1
 BW -| 5 X      |--  *8-bit bus       16-bit bus
PCI -| 6 X      |--  *PCI-OFF         PCI-ON
DSP -| 7 X      |--  *DSP-OFF(Reset)  DSP-ON
 SR -| 8 X      |--  *SmartReflex-Off SmartReflex-On
     \----------/
        SW3

Boot Modes:
(BM[3:0])            (BM[3:0])
(when PCI-OFF)       (when PCI-ON)
-------------------------------------------
*0000:EMU
 0010:HPI-16         0010:PCI w/o auto init
 0011:HPI-32         0011:PCI w/ auto init
 0100:EMIFA
 0110:I2C
 0111:NAND
 1000:UART0
 1001:Emulation
 1010:VLYNQ
 1011:EMAC
 1110:SPI
 ELSE:N/A

PCI Configuration Switch Settings (07/11/07)
Here is the PCI configuration for SW3 on the DaVinci HD board.

For PCI w/ auto init:
     /----------\ 
     | # OFF ON |
BM0 -| 1     X  |--  BM[0]
BM1 -| 2     X  |--  BM[1]
BM2 -| 3 X      |--  BM[2]
BM3 -| 4 X      |--  BM[3]
 BW -| 5 X      |--  8-bit BusWidth
PCI -| 6 X      |--  PCI Enable
DSP -| 7 X      |--  DSP Off
 SR -| 8 X      |--  SmartReflex Off
     \----------/
        SW3

For PCI w/o auto init:
     /----------\ 
     | # OFF ON |
BM0 -| 1 X      |--  BM[0]
BM1 -| 2     X  |--  BM[1]
BM2 -| 3 X      |--  BM[2]
BM3 -| 4 X      |--  BM[3]
 BW -| 5 X      |--  8-bit BusWidth
PCI -| 6 X      |--  PCI Enable
DSP -| 7 X      |--  DSP Off
 SR -| 8 X      |--  SmartReflex Off
     \----------/
        SW3 

Reference voltage noise (08/22/07)
On all previous assemblies ( B, C ) the TLV431 does not over-drive the ADV7343 internal reference correctly. This causes noise on the display. The solution is to use the AD7343 internal reference. This can be done by removing R171, R175, and U16 on all previous assemblies. This change has no software affect on the boards.